Testsystems
All example measurements
  • PSM
  • 8 poles
  • V-shaped architecture
  • Weak/damaged magnet

8-pole PSM rotor with one weak pole

On this page you get an insight into the evaluation of a PSM rotor, measured with our sensor array. The measurement was taken on the rotor shown in the video.

Watch the measurement on the bench 0:17

How the rotor is built

Each pole holds two magnets buried in a V shape. Along the rotor, each of them is split into 4 pieces: 8 magnets per pole, 64 in total.

The field leaves the rotor at the north poles and re-enters at the south poles beside them. It is densest at the edges of the poles, which is why every pole is stronger there than at its centre. A small part closes right at the pole boundary, through the iron between the poles: there the field briefly turns back. Both are typical of buried magnets and can be seen in the field map below.

Schematic cross-section of the 8-pole rotor with two magnets per pole, buried in a V shape, and the field lines running outside the rotor from each north pole to the south poles beside it. The poles are numbered 1 to 8 at their measured angles; pole 2 is shaded. NSNSNSNS 12345678 0°
Schematic, not to scale. Poles at their measured angles, 0° at the top, clockwise. Field lines run from north to south; pole 2 shaded.

Where pole 2 is weaker

Schematic side view of the rotor as a cylinder, looking at pole 2. Along each pole lie two rows of 4 magnet pieces. Marked red is the area of pole 2 between about 80 and 100 mm axial position, where the field is weaker.Pole 2 · S: weaker between about 80 and 100 mmPole 1 · NPole 3 · N20406080100120140Axial position (mm)
Schematic, not to scale. View onto pole 2; the end face shows the cross-section. Dashed: the magnet pieces. Red: where the field is weaker.

Field map

The view shows the rotor's radial magnetic field, measured around its circumference. You can switch between the 2D map and the 3D landscape.

What the view shows

  • An 8-pole rotor: north and south poles alternate around the circumference.
  • Pole 2 (centre at 68°) is clearly weaker between about 80 and 100 mm axial position, which strongly suggests a damaged or weak pole.
  • Note especially the steep peaks at the transitions between the poles. The edges are sharp and consistent across all poles. This is thanks to the fine sampling of our measurement. With larger measuring distances or coarser sampling, the transitions would be softer.

Drag to rotate the view · Right-drag to move the object · Ctrl + mouse wheel to zoom

Single-signal view

The flux density over one revolution at three axial positions: channels 1, 16 and 22. In our application you can select any channel; here we give you a preview of these three.

What the view shows

  • Channel 1 (17.5 mm): this channel lies at the edge of the rotor. At poles 5 to 8 the signal swing is somewhat weaker than at poles 1 to 4.
  • Channel 16 (70 mm): at this position, pole 2 already shows a clear drop in the signal compared with the other poles.
  • Channel 22 (91 mm): this channel lies in the weak area of pole 2. It shows clearly how strongly the flux density drops at pole 2.

Drag to zoom into an area · Shift + drag to pan · Double-click to show everything

Field FFT

The field broken down into orders per revolution. With 8 poles, the fundamental is order 4. Ideally, the signal should consist only of odd multiples of 4; all other orders are disturbances. In our application you can display the FFT at every measured position; in this demo we limit it to 5 channels.

In the plot, compare in particular the spectra at axial positions not affected by the faulty magnet, such as channel 11 (52.5 mm), with those in the range of 80 to 100 mm. You will find that the disturbances are clearly stronger in the latter.

Fundamental (order 4) Odd multiples of order 4 Other orders Mean axial position (77.0 mm)

Drag to zoom into an area · Shift + drag to pan · Double-click to show everything

This is just an excerpt

If you would like to see the key figures and further views of the measurement, feel free to get in touch. We will arrange a demo with you.

Contract measurement

Test it on your own rotor first

Send us one of your rotors, or we come to your plant in Germany with a mobile test bench. You receive the 3D model of the field, the pole analysis and the measurement data – before you decide on a test bench of your own.